The LM/LM are dedicated motion-control processors designed for use with a variety of DC and Details, datasheet, quote on part number: LM 2 Independent LM PWM-output servo motor controllers .. AN, AN Application note and LM/LM Datasheet walk you. LM datasheet, LM circuit, LM data sheet: TI – LM/LM Precision Motion Controller,alldatasheet, datasheet, Datasheet search site for Electronic.

Author: Fejin Mikale
Country: Slovenia
Language: English (Spanish)
Genre: Business
Published (Last): 9 June 2011
Pages: 35
PDF File Size: 2.41 Mb
ePub File Size: 7.22 Mb
ISBN: 537-3-43804-919-4
Downloads: 73080
Price: Free* [*Free Regsitration Required]
Uploader: Doktilar

Can someone explain what are the possibilities and the reason that explains why after connecting a motor, LM can get killed instead? Will there be a problem. Should I use two separate power supply for powering ICs and motor?

Initially seems a little ok,but after a couple of runs the nightmare seems to reappear. How do I identify if the IC is burnt or not? Figure 10 illustrates two typical trapezoidal ve- locity profiles. Internet is down due to Taiwan Earthquake!!! The LM uses this infor- mation to affect the move by accelerating as specified until the maximum velocity is reached or until deceleration must begin to stop at the specified final position. I’ve always had good luck with motor controllers like the L, but you’ve not been all that specific about your exact needs.

LM Datasheet(PDF) – TI store

Use a Logic Analyser to understand the actual timing, then adjust the timing through tweaking the PBasic coding in the basic stamp. As long as you don’t ‘fall in love’ with video processing, things would be quite similar to programming in PBasic. Or do I need interfacing components?


So, a clock is necessary for LM to function. Must I go with a micro-P capable of working 16bit wide bus? You can either build a 16bit wide datashet with two bytes or go with a 16bit or 32bit processor. Right now, I am trying to comprend how the video juggles memory with something referred to as tiles.

That’s the reason why I insist on sticking with LM Design Requirement for my part. The LM uses this infor. Hwang Xian Shen, Puddleby-on-the-Marsh. I agree with Bruce that this is not the best device to use with a Stamp because of the number of lmm629 required.

At any time during the. I managed to find a pc with a faster internet access not through the phone line and looked at the datasheet for L Or during l6m29 micro-P selection, I have to go with one based on a 16bit core.

(PDF) LM629 Datasheet download

Sign In or Register to comment. Did I caused something to locked up along the process. Will consider this as one of the option if the learning curve is not that steep and development time is short. While the SXes will tolerate 30ma, less is better. In the position mode of operation, the host processor specifies acceleration, maxi- mum velocity, datasheeet final position. It will tolerate 5. So you get more speed and simpler code.


My count is 13 total. I was thinking that the RST is an asychronous input and so might not need a clock as long as I pause long enough, correct me if I am wrong in this line of thought.

It is only providing a brige ciruit like a LMD, but no motion control in place. What is wrong here?

Quick Links Categories Recent Discussions. You certainly will have more speed. If I were to connect a 8Mhz clock and power up, then the return status byte would be FF. That is where you might find a steep learning curve. If the motor is unable to maintain the.

Interfacing problem with Basic Stamp BS2px24 and LM — Parallax Forums

I thought the clock is used mostly by the encoder. Still, I was wondering what is preventing the stamp from communicating effectively with the motor controller. I am in Taiwan too.

Can anyone advise how to do it? Tried lm269 means and even different clocks circuits, still doesn’t seems to work out. As shown by the status, it is staying at hex In the position mode.

LINUX is just fine.

If the motor is unable to maintain the specified velocity which could be caused by a locked rotor, 9 www.