HP DESIGNJET T1300 SERVICE MANUAL PDF

Manuals or user guides for your HP DesignJet T in Printer. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration. Service Manual and more parts for CRA DesignJet t in eprinter.

Author: Gogore Minos
Country: Serbia
Language: English (Spanish)
Genre: Business
Published (Last): 23 December 2016
Pages: 51
PDF File Size: 14.72 Mb
ePub File Size: 6.43 Mb
ISBN: 283-8-89657-956-5
Downloads: 85425
Price: Free* [*Free Regsitration Required]
Uploader: Tugore

Power cable of the Scanner is failing Corrective action: Disconnect the four connectors from the Left Ink Supply Station.

Use the spanner provided in the tool kit to remove the 13 mm locking nut that secures the Encoder Strip to the Encoder Strip Spring. Remove the servie cover of the Carriage PCA. Assembly on page All. Remove two T screws from the Trailing Cable Support.

Engine Cables Kit on page Press OK to continue or press Cancel to exit the calibration. Be servife with the paper sensor cable. Page 66 Problem Description: The Touch Control Panel prompts you to confirm that the dummy printheads are correctly inserted. Remove the black end of the spindle from mnual product, then the blue end. Calibrate the Scanner The purpose of this is to perform a full calibration of the scanner consisting of the following tests: Emergency firmware upgrade with USB flash drive Check that the encoder sensor is correctly connected to the Carriage PCA.

Pull both Data and Power Harness under the left arc On the other side of the unit, detach Power and Data cables from cable ties. Hold the calibration sheet from both sides and place it facing the arrow in the centre of the sheet in front of the Page icon present on the input tray of the scanner.

  LIBERACION SANDOR MARAI PDF

HP Service Manual for CRA DesignJet t in eprinter

Load the Scanner IQ plot that you printed previously in the Scanner input tray. Leave the Belt Tensioner in place. Carefully lift the Ink Supply Tubes guide enough until you can slide it forwards out of the product. Each arc represents a CIS element. Center Covers Front 2 of 3. YZ troubleshooting, first look for structural damage.

Open the CIS and remove five T screws. For information about using these products, refer to the corresponding User and Quick Reference Guides.

Unlatch the CIS Cover. Remove the tape securing the cable bundle. Tools 1 on page Converger on page Front Cover on page Reboot Manuual System Error: Make sure all the ferrites are removed. Introduction on page Slide up the Right Ink Cartridge Door to remove. Collapse the Pinchwheel Alignment Tool to remove it. Remove a white slider. Remove two T screws that secure the to the product.

HP DesignJet T1300 44-in Printer User Guides

Detach the roll cover from the product on the right-hand side. Scanner Position Sensor failure Corrective action: If the issue is new and the issue happens since the first boot, do not replace the HDD.

If step 1 did not resolve the issue, you can use Service Tools to clear additional information that could be causing the issue. Product Support on page A firmware upgrade will not always solve the problem.

HP Designjet T790 / T1300 / T2300 series. Service Manual

Lower the Media Lever. This gives you access to the printheads.

  BAJANDAS NEURO OPHTHALMOLOGY PDF

Press the OK key to start loading the paper. Remove the two T screws that secure the left Window hinge locking plate to the Top Cover. Remove the circilp on the other end of the piston gas using a flat screw driver, ensure that the circilp is kept under control by holding it with your left hand as shown in the picture. Connecting the Data Harness and ISS Harness Cable Wether you are reconnecting or replacing the cables it is important that the ISS Harness and Data Harness are connected correctly to their corresponding connectors designket the Engine PCA, it is possible to swap them over in error and connect them into each others connectors, and cause a Scan Axis movement requires too much force or energy.

DESIGNJET T/T ePrinter series & T eMFP series Service manual

To change an ink cartridge there are two methods, the first is shown below by using the ink tab, the second method is to access the main menu option refer to the User’s Guide for further details. Before executing this test you should run the Scan Axis, Media Drive and Carriage tests to ensure that each of these subsystems is operating correctly.

Install only new parts recommended by HP for this eervice.