Hobbymat MD65 Lathe (and Prazimat SD): Operating Manual, Maintenance Manual, Exploded-components Spares List, Wiring Diagram and screwcutting. Some photos of My Hobbymat MD65 Lathe. The Hobbymat was made in Eastern Germany until fairly recently and was designed for The Specifications are. Hobbymat md65 lathe instructions manual by andrew_mazurkiewic_2 in Types > Instruction manuals.

Author: Gubei Karamar
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Sex
Published (Last): 20 April 2004
Pages: 443
PDF File Size: 12.53 Mb
ePub File Size: 15.83 Mb
ISBN: 666-3-54748-736-8
Downloads: 37808
Price: Free* [*Free Regsitration Required]
Uploader: Danos

Is this a cause for concern? Nothing I’ve tried seems to loosen it That’s how mine is. Back to home page.

Hi Phil, I have had a MD 65 since new must be 30 years. Zero play on the headstock spindle, and it works pretty nicely but for a few things All manuals are scanned at high resolution and supplied as a top-quality print, bound and on a superior g paper.

Looking for any advice on this machine. David — David Littlewood. When not cutting, I am assuming is runs smooth and there is no vibration?

Hobbymat MD65 & Prazimat SD300 Lathe Operator’s Manual & Parts Manual

Also, a lot of the set-screws seem to have gotten quite black and mucky, as has most of the bed and the compound there’s hobbymst section of bright metal where the rotating section of the compound sits. A link to download the PDF document will be emailed to hobbgmat PayPal address, mabual with a password.

Thanks for all the replies and help. Slight deviation from the manual but nothing major. Some aluminum is stubborn, but with everything on the machine working and adjusted properly, the right geometry on the cutting tool ensuring the cutting tool is also on centerenough support on the workpiece, the right spindle speed and feed rate, and perhaps a bit of cutting oil, you should be able to get a beautiful finish. Philip, I have not seen the Hobbymat headstock, but I’d bet a substantial sum that the 3 holes you mention are made for use with a special tool.


Hobbymat Md 65 Manual

The item may have some signs of cosmetic wear, but is fully operational and functions as intended. I had to make wrench for the chuck. Back to home page Return to top. Rubber is fine if it is just grunge you are over coming but copper or steel but be better to shock it loose. Nov 28, For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.

The dials are fitted with flat springs, sounds like they needs a good clean. Start of hobbumat to list layer. I might try a few different change gears to find one which provides a bit more resistance. Spares are available from Essell Eng.

The lathe has a D bed. NO hacksaw and NO chisel,please. This listing has ended.

Hobbymat MD65 & Prazimat SD Lathe Operator’s Manual & Parts Manual |

Is this still the best stuff to use, or should I use a different solvent instead? Welcome to the forum! And your RL job is butcher????. Aug 11, Unless otherwise stated, all manuals are in English.



You don’t mention whether the holes are on the face or circumference of the nut. Put something, a bit of floorboard, piece of steel plate on the bed between the saddle and the headstock, wind handle and total resistance is achieved. Suggestions for good books on metalwork would be much hobbmyat Aug 13, For details of Hobbymat lathes see: Have they taken a ‘set’ during disuse?

The electrical manuak can be a bit delicate but everything else can be treated like any other metal item. They move, but not particularly easily. Aug 04, I hid md655 from Mrs Naut under a sheet, and over the course of the next week disassembled it from the back of my car without anyone being the wiser, secreting the various parts in the garage and even under the bed.

It was used, but in like new condition.

So I’m almost there Bazmonaut’s site is very good. The cameos of his ‘helpers’, pictured on the Lathe Rebuild page, are endearing.

Of course the machine has already been leveled and secured to a stable work area of some mass, yes? The tailstock works in the same way.

The console even had a little TV on it.