Siemens products may only be used for the applications described in the catalog The SITRANS FUE energy calculator has been developed for Siemens. Fine Controls are the official Technology partner for the Siemens instrumentation product range type FUE, Inline Ultrasonic Energy Meters, In Stock. Dec 4, Siemens Industry Automation Division introduces the Sitrans FUE thermal energy calculator, designed for use in hot water, chilled water.
|Published (Last):||14 January 2005|
|PDF File Size:||8.37 Mb|
|ePub File Size:||13.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
Siemens SITRANS FUE950 Operating Instructions Manual
Page 24 pipe by heating low temperature Calculator combined Forward “hot line” By heating: Temperature sensors are of the same pair. Short press Short press 4 sec. Page 30 The display is also switched off, but can be switched on again by pressing any button.
The board contains 2 terminals marked as 24 and 25, which are typically connected to the Fie950 master M-Bus controlling centre. Material compatibility Siemens Flow Instruments can provide assistance with the selection of wetted sensor parts. Page of 72 Go. The functions and settings of the outputs can be freely programmed using a software tool and the IrDA interface, e. Page 72 Further information www. M-Bus communication description is available on request, please contact Siemens.
Short press 2 sec. Page 37 M-Bus or RS module is not used, pulse ziemens module can also be installed in slot 1. Enter text from picture: M-Bus or RS module is not used, pulse input module can also be installed in slot 1.
Technical Support If you have any technical questions about the device described in these Operating Instructions and do not find the right answers, you can contact Technical Support: Month loop Display menu loops The various loops will fuee950 the following information: Note Siemens Flow Instrument defines sensors as non-repairable products.
Page 32 The functions and settings of the outputs can be freely programmed using a software tool and the IrDA interface, e. SW-tool Leak detection water meter at Disables: Page siemenw In 1 Pulse 1 In 2 Pulse 2 counter counter 6.
Functions and settings can be checked via display menus 3 and 4 and freely programmed using a software tool and the IrDA interface. By pressing ‘print’ button you will print only current page. Short press Short press Short press 2 sec.
In case of deviating environmental conditions, energy meter has to be remounted regularly for service. Tariff loop only visible if activated 6. Close lid and check meter for correct operation by pressing push button. However, the full responsibility for the selection rests with the customer and Siemens Flow Instruments can take no responsibility for any failure due to material incompatibility. Connect shield to grounding at flowmeter.
Connecting Making cable entries Make a circular hole by dismounting rubber grommet using a flat plier. Carefully slide plug onto board. Sitrans Fue And Fus Skemens connection of flowmeter, see flowmeter operating instructions. Product information on the internet http: Figure S – User sealing 3.
Page 56 E – 9 Display Battery empty checked Monitors: Tariff energy 2 1. Page 61 RS output Type The optional plug-in RS communication module is a serial interface and permits data exchange with the calculator.
The settings and functions for the modules can be changed via a free using software tool and the IrDA interface of the FUE Proper transport, storage, installation, assembly, commissioning, soemens and maintenance are required to ensure that the products operate safely and without any problems.
Ultrasonic flowmeters 7me portable flowmeter pages. Functions and settings can be checked via display menu 3 and freely programmed using a software tool and the IrDA interface.
Making cable entries Make a circular hole by dismounting rubber grommet using a flat plier. Only terminals 10 and 11 will be connected to the Siemens flowmeters. The 2 resistors must be mounted between terminals 57 and 58 in the MAG terminal socket.
The date and time remain actual but none of the measuring functions work, incl. Technical Support Service and maintenance 7.
SIEMENS SITRANS FUE – ENERGY CALCULATOR | Fine Controls Ltd
Dimension Drawings Dimension drawings Power Supply Options If no mains slemens is connected, a back-up battery in the mains unit provides the power supply. Page 57 SW-tool Leak detection water meter at Disables: RS output Type The optional plug-in RS communication module is a serial interface and permits data exchange with the calculator.
Catalog process instrumentation http: Service and maintenance 7. Short press Returns to menu 2. Page 11 Before removing the inner plastic cover the mains power shall be switched off. Scope siejens delivery may vary depending on selections at ordering. Page 46 Operation hardware 6. The label seal on the calculator see figures Page 49 must not be damaged!