FERROLI WFL4+P7 PELLET ΤΑΞΙΑΡΩΝ. By – Ποιότητα & Οικονομία · Updated about 5 years ago · Taken in περιστερι · Already tagged. Gorilec na pelete Ferroli z visokim učinkom in omejenimi emisijami za kotle na trda goriva razreda 3 EN , zanesljiv, enostaven za uporabo in vzdrževanje.
|Published (Last):||13 January 2006|
|PDF File Size:||15.23 Mb|
|ePub File Size:||3.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
As far as I know there is no parameter that sets a temperature that will start the cycle. Ignition is detected by the light sensor. Couple weeks ago the burner changed. The company that installed ferroli one insisted in putting a voltage regulator.
There are allot of those in our area and the price is half of the pellet. When we feerroli our wood burning boiler it was murder when the wind was blowing, the garage was forever filled with smoke and the Vedetta has cured this problem, and now with the new Ferroli the house is toasty warm. After this, the heating element is powered and the fan will blow slowly until the pellets ignite. The problem is that sand will not generate any heat and chunks of glass will form in the grille so that you have to clean it more often the fan will blow away any ash but not the chunks of glass.
Not that I care but the guy who brought me olive cores says that I need more air inside boiler. So big, that the burner was blocked from the very beginning. Verroli size is according to the manual Wish You all the best! The language barrier is ferropi much.
As you can see, if you increase t07 you also increase the period in which pellets are burned t07 — t13 while keeping t13 the same. The burner was getting blocked all the time because the initial quantity ferrlli pellets before ignition was too big. During this time only the fan works. Carissimi per ricevere la newsletter come devo fare, a chi devo scrivere??? ferroki
What you can try is to reduce the power level of the burner, by reducing the fan speed fan set point and the pellets quantity auger activation time. Helloand thanks for the respond. Else, it is usually the motor. So our next job for Spring if not earlier is to purchase the Ferroli feroli, then there should be touch wood no problems.
Stuck SUN P7 pellet burner – how to fix.
So I would deal with this problem as o7 as possible. I think on you case it should be 0 no modulation. Try to reset everything to default values, see the table. To go back to the subject. As for the unburned pellets, some people compained about it too in the ferdoli version of this article but nobody knows why it happens. It will just stop as it does now. Before playing with that I would like to ask if anyone knows, what decides when are power levels changed?
A lot of ash will be deposited in the chimney, especially the horizontal pipes.
The quality of pellets is important. It was photo cell.
You should call an electronist to do it if you have no experience. And so, little by little, the loading tube was filled with pellets. Thanks again for your assistance, it is very much appreciated. Usually the burner starts when the thermostat orders it if u03 is 0 or according to a weekly schedule if u03 is 1 or 2. Also, buy some high quality pellets a sack or two and see if the problem dissapears. Can anyone help please??? The fan ferrpli air inside but that air can go out on the chimney and also up through the auger pipe.
It spend kg pellets a day. And what if I increase power level to 2?? This year i will try to use some olive core and skin pellets made here in my country by a local factory which buys the raw material from the oliveoil factories!!
Stuck SUN P7 pellet burner – how to fix. – Jurnal
Any feedback is appreciated. Anyways, again thank you allot for all of your input, thank to you I understand how burner works. Does any one knows how to solve this issue. But this does not bother me too much since, after restart, it keeps running. There are burners with a different design that are not so sensible to pellet quality. Once I solve that, I will jump back on almond shells and try to optimize the system. And then it repeats. Pellets of good quality have pretty large chunks of wood inside them you can see this when you break them.
Beside the fact that t04 is used only on startup not the problem in my casethis small bridges that you mention, could cause the problem.
BRULEUR a Pellet FERROLI Sun P7 | eBay
To clean it, you also have to take the red cover off. Right below the display disappear the 3 and the little stick, after this ferroll appears that 0, shortly after the blowing begins and at the same time then comes the FH. So, the whole olive cores load, burn and give good results. Are the pellets of good quality? Thank you for the information. I do not know if this is normal or some problems with controllers.