EN ISO 6507-1 PDF

hardness test —. Part 1: Test method. Matériaux métalliques — Essai de dureté Vickers —. Partie 1: Méthode d’essai. STANDARD. ISO. Fourth edition. Purchase your copy of BS EN ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. I.S. EN ISO is the adopted Irish version of the European . The text of ISO has been approved by CEN as EN ISO.

Author: Galmaran Akitilar
Country: Zambia
Language: English (Spanish)
Genre: Life
Published (Last): 10 March 2012
Pages: 21
PDF File Size: 15.9 Mb
ePub File Size: 11.62 Mb
ISBN: 187-7-23163-414-3
Downloads: 57354
Price: Free* [*Free Regsitration Required]
Uploader: Akinozuru

There is no correction of the hardness values with respect to the error. It is strongly recommended that this procedure be applied for a maximum of one year after the successful passing of a direct verification.

The support surfaces shall be clean and free from foreign matter scale, oil, dirt, etc. The main task of technical committees is to prepare International Standards.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. As a reference, an EA guideline [7] is available. In this case, an estimate of type A standard uncertainty may be obtained from the statistical analysis of repeated indentations into the test piece.

NBN EN ISO 6507-1

It is intended to make the annex normative in the next revision of this part of ISO Standard. These performance uncertainties reflect the combined effect to all the separate uncertainties indirect verification.

To set a reading intention, click through to any list item, and look for the panel on the left hand side:. For dated references, only the edition cited applies. Your reading intentions are also stored in your profile for future reference. Reference number ISO Setting a reading intention helps you organise your reading.

If the difference is greater, this shall be stated in the test report. The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the cylinder. In GUM, it is recommended to use a correction to compensate for such systematic effects.

The Amber document status indicator indicates that some caution is needed when using this document – it is either: Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. If the measuring system fails this test, appropriate action should be taken. It makes it easy to scan through your lists and keep track of progress. Care should be taken, if standard uncertainties of type A and B are summarised, that the contributions are not counted twice see Clause 4 of GUM: The error is no longer in the calculation of the uncertainty but all determined hardness values have to be corrected by b or Ucorr has to be increased by b.

  COURS DE MACROECONOMIE S2 PDF

NBN EN ISO | NBN

The work of preparing International Standards is normally carried out through ISO technical committees. Their committees work with the manufacturing and service industries, government, businesses and consumers to facilitate the production of British, European and International standards. ISO consists of the following parts, under the general title Metallic materials — Vickers hardness test: The error b step 10 can 65007-1 expected to be a systematic effect.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Type Document Web address https: NOTE There is evidence that some materials may be sensitive to the rate of straining which causes small changes in the value of the yield strength. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

The chain starts at the international level using international definitions of the various hardness scales to carry out international intercomparisons. Free to use BIM project management tool provides step-by-step help to define, manage and validate responsibility for information development and delivery at each stage of the asset life cycle in level 2 BIM projects.

BS EN ISO – Metallic materials. Vickers hardness test. Test method

Test method 1 Scope This part of ISO specifies the Vickers hardness test method, for the three different ranges of test force for metallic materials see Table 1. The procedure for the determination of U is explained in Table D. Verlag Berliner Union Stuttgart,pp Again there may be more recent versions of the document. NOTE 1 A strict comparison of hardness values is only possible at identical test forces.

  AM2901 DATASHEET PDF

Please log in to set a read status. Due to the small depth of Vickers microhardness indentations, it is essential that special precautions are taken during preparation.

Naturally, direct calibration and the verification of these machines should be at the highest possible accuracy. It should be noted that for anisotropic materials, for example those which have been heavily cold-worked, there will be a difference between the lengths of the two diagonals of the indentation.

Unless otherwise specified, no part of this publication may be reproduced fn utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

In M1, the error limit, that means the range in which the machine is allowed to differ from the reference standard is used to define the source uE of the uncertainty. Document Status Indicators The Green document status indicator indicates that the document is: This is the base of M2.

For automated measuring systems this standard should be applied accordingly. Specifies the Vickers hardness test method, for the three different ranges of test force for metallic materials. How do I set a 650-71 intention To set a reading intention, click through to any list item, and look for the panel on the left hand side: Here’s an example of what they look like: No deformation shall be visible at the back of the test piece after the test. e

This is particularly true for low-force Vickers hardness tests and Vickers microhardness tests, where the principal limitation will arise in the measurement of the diagonals of the indentation.

M2 may lead to smaller values of uncertainty. Ihre Klassifizierung und Auswirkung auf die Messwerte. NOTE Other values e.

ISO shall not be held responsible for identifying any or all such patent rights. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.