international certification bodies for its quality system and environmental management system. E5jK-T Series. E5CK-T. E5AK-T/E5EK-T. 1/4 DIN. 1/8 DIN. Omron E5AK Controllers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Omron E5AK Controllers. E5AK-TAA AC Omron Automation and Safety Controllers PROCESS CONTROLLER datasheet, inventory, & pricing.

Author: Fezilkree JoJojar
Country: Lebanon
Language: English (Spanish)
Genre: Automotive
Published (Last): 13 November 2013
Pages: 158
PDF File Size: 12.70 Mb
ePub File Size: 2.73 Mb
ISBN: 415-3-63779-881-9
Downloads: 63614
Price: Free* [*Free Regsitration Required]
Uploader: Fenrikazahn

When a potentiometer is not connected to the controller, [] is displayed on the No. Don’t show me this message again.

Conventions Used in This Manual J Meanings of Abbreviations Sometimes the following abbreviations are used in parameter names, figures and in text explanations. The display changes to [ ] 0mA calibration display.

Set the STV output to 5V. To give Function priority to stability, increase the set value of this parameter. SP ramp function is enabled. This example describes how to calibrate voltage input when the trans- fer output function is supported. If the key is pressed for less than one second, the parameters are switched.

Page 35 This description assumes that the controller is operated under the fol- lowing conditions. Operating Condition Restrictions The upper limit is set for the heating side positive valueand the lower limit is set for the cooling side negative value as shown in the follow- ing figure.


In other words, you cannot switch between the auto and manual operations by key operation. Output 1 second min.


In this mode, you can Be sure to turn on omon power supply to the load either before or simultaneously with the start of Temperature Controller opera- tion. When the value on the No. LBA, 7 to 9: The fol- lowing diagram shows the relationship between option units and mounting positions.

For e5aak on how to use the controller and parameter settings, see Chapters 2 onwards. Page 24 1 Remove the power board and option boards in the order shown in the following diagram.

Omron E5AK-AA2-500 Processor/Controller

Controllers must not be closely mounted vertically or horizontally. Also, response are displayed without spaces between frame items. J Output Unit Ratings and Characteristics Ratings and characteristics conform to the output unit mounted on the controller.

About The Displays Each press of this key switches between the auto and manual opera- tions. F Dead band The dead band is set with the set point as its center. SP tracking function is enabled. Page 3 Conventions Used in This Manual J Meanings of Abbreviations Sometimes the following abbreviations are used in parameter names, figures and pmron text explanations.

Remote E5ka Monitor SP tracking function is enabled. So, 3-position control is made possible. During operation of the ST function, the power on the load side connected to the control output must be turned ON at the same time or before start of E5AK Function operation.


About The Communications Function 1. Use this chapter as a reference guide. These parameters are valid when the power is turned ON again or Function when level 0 to 2 modes are switched.

ST stable range dard control and advanced PID control. Pay Attention to the Following when Installing this Controller F If you remove the controller from its case, never touch nor apply shock to the elec- tronic parts inside.

OMRON E5AK User Manual

The following figure shows the required device connection. In this mode, you can set the communications conditions, transfer output and event input parameters to match the type of option unit set in the controller.

The Omroon controller is calibrated before shipment from the factory. Dead time will be measured from the time the Temperature Controller starts operating.

No part omrin this publication may be reproduced, stored in a retrieval system, or trans- mitted, in any form, or by any means, mechanical, electronic, photocopying, recording, recording, or other- wise, without the prior written permission of OMRON.

Also, a lower limit value larger than the upper limit e5xk may be set. These abbreviations mean the following. The setting range varies according to this output data. Page of Go. Enter text from picture: Page AT hysteresis 0.