Dome Camera Installation Manual Weatherproof and Indoor versions www. Contents Introduction. Menu System Manual. Page 4 of 1. THE DENNARD TYPE DOME CAMERA. The Dennard Dome Camera is a precision unit, offering a wide. The Dedicated Micros Camera has a number of features which can be selected by the System. Supervisor when the dome is installed. Any of these can be.
|Published (Last):||2 August 2007|
|PDF File Size:||15.33 Mb|
|ePub File Size:||3.35 Mb|
|Price:||Free* [*Free Regsitration Required]|
The mechanism has been designed to fit within the existing housing allowing it to remain compatible with the wide range of Dennard accessories and brackets. View 260 content on SecurityInformed.
Patrol mode is cancelled with any manual zoom action. The monitor shows nothing but scrolling lines but I do see a flicker when I drive the joystick. Do not show this again. Up the Coax Configuration Switch settings The switches are color coded, blue and yellow, and are located inside the dome camera housing. Dennarr Micros is pleased to announce that the Dennard Precision Dome is being upgraded with new features including:.
Check the dome address switches are correctly set for the controller being used. The link must be left on permanently. Unscrew the 6x fixings securing the outer hemisphere to the casing and dsnnard.
Introduction The Dedicated Micros camera is a precision unit, offering a wide variable speed range, together with a large pre-set memory for positions, tours and alarm responses. There is no prepared cable included, the connector for the camera is included. For standard ceiling mounted domes attach the supplied safety bond; 1.
Remove the selected tile that will have the dome mounted to it. Radiated Emissions Standard, suitable for Commercial or Residential use. The DM Dome can be controlled by one of three methods.
Dennard 2060 PTZ Speed Dome Camera 36 x Optical Zoom with Swan Neck (Fully re-furbished)
Solution Reboot the controller with the joystick self centred. Dedicated Micros range extended to include a new indoor dome.
The location of the switches is also shown. Grip the camera platform, accessible through the camera viewing slot, to adjust the tilt position. Page 26 Termination All Dedicated Micros domes are fitted with a termination switch, shown above.
206 Introduction The Dedicated Micros camera is a precision unit, offering a wide variable speed range, together with a large pre-set memory for positions, tours and alarm responses. Appendix A DM Fixed Attitude Dome Camera – Setup Telemetry cameras can be positioned remotely, fixed atitude cameras dennarv manual adjustment to position the camera.
Fit the safety bond between the enclosure denmard the mounting disk. Don’t show me this message again. Control Switches – Indoor Dome Thread the cable from the bracket throught the cable entry hole in the bottom of the bracket casting, then fit the bracket shown above left.
Dennard Dedicated Micros D PTZ Dome Camera CCTV | eBay
For this application, Dedicated Micros offer an optional corner bracket, DM to adapt the standard wall bracket. By ramformerApril 3, in General Digital Discussion. Set each switch to its desired position as shown in the table.
Always support dome with bond prior 20660 mating connector. Offer the dome enclosure up to the ceiling mounting disk, shown upper right engaging the screw heads C into the keyhole slots on the base of the dome F enclosure. Sign up for a new account in our community.
Always support dome with bond prior to mating connector B. Grip the inner hemisphere and rotate to adjust the Pan position of the camera.
Dennard Dedicated Micros 2060 D PTZ Dome Camera CCTV
Remove and retain the four screws securing the shield to the head and lift off the shield. Tile Mounting – Weatherproof Dome mm mm Attach the mounting disc A to the dome in the chosen position and use 3 of the existing M4 dome hd screws to attach the hemisphere to the dome. Page 11 C into the keyhole slots on the base of the dome F enclosure. Solution Reboot the controller with the joystick self 20600. Fit the supplied safety bond E to an attachment point in the ceiling.
Mounting brackets may have been ordered and delivered separately. The RS wires are only connected when an RS controller is being used.
Sign In Sign Up. Mounting brackets may have been ordered and delivered separately. The external camera is weatherproof IP rated. This operation should be carried out in an office type environment to avoid ingress of moist air. Fit the supplied safety bond E to an attachment point in the ceiling. Use the serial port connection if serial telemetry is required. Open the Technician menu see Operation and Programming manual for details on accessing the menu.