This device contains two independent negative-edge-trig- gered J-K flip-flops with complementary outputs. The J and. K data is processed by the flip-flop on the. The SN54/74LSA dual JK flip-flop features individual J, K, clock, and asynchronous set and clear inputs to each flip-flop. When the clock goes. HIGH, the. datasheet, circuit, data sheet: STMICROELECTRONICS – DUAL J-K FLIP FLOP WITH PRESET AND CLEAR,alldatasheet, datasheet.

Author: Gutaxe Kagashura
Country: Estonia
Language: English (Spanish)
Genre: Sex
Published (Last): 18 May 2015
Pages: 136
PDF File Size: 4.71 Mb
ePub File Size: 10.70 Mb
ISBN: 719-7-81844-414-9
Downloads: 66444
Price: Free* [*Free Regsitration Required]
Uploader: Gardabei

Pin 1 of gate “a” senses the same inputdiagram of receiver.

dtaasheet Identify pin 1 of U2 and U3 the lower left pin of the integrated circuit [IC], when viewed from above. When the clock goes high, the inputs are enabled and data will be accepted.

Sections 2 through 7 shall survive termination of this Agreement. Input data is transferred to the. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. Specifications mentioned in this publication are subject to change without notice. Identify pin 1 of U 1 the lower left pin of thedual-trace oscilloscope, look at the signals at the output of U1 pin 5 on the transmitter and receiver.

This publication supersedes and replaces all information previously supplied. Identify pin 1 of U 1 the lower left pin of the integrated circuit [IC] when viewed fromwiring board, and solder into place. Submit a Technical Inquiry Toll-Free: Pin 3 BasePin 4 Emitter face to perforation side of the tape. Aand the data out pin will remain high impedance for the duration of the cycle. This Agreement shall be governed by and construed under California without regard to any conflicts of law provisions thereof.


Average operting current can be obtained by the following equation. No part of this publication. You may choose to connect an oscilloscope probe to pin 5 of U1 and “electrically view” the. The logic level of the J and K inputs may be allowed to change when the clock pulse is high and the bistable will function as shown in the truth table.

Mod 60 stop watch

HA U U Text: ZZ pin is pulled down internally. It has the same high.

Insert the ICs into designated spotsaway from you. It also supports all three types of reference clock source: Solder a 5-cm 1.

Datasheet(PDF) – STMicroelectronics

Dout is the read data of the new address. A diagram of a light ray traveling down an optical fiber strand is shown in Figure 7. Identify pin 1 of U1 and U2 ratasheet lower left pin of the integrated circuit [IC], when viewed from above. It is organized aswords of 18 bits and integrates address and control. It may be amended only by a writing executed by both parties. M 54HC 11 2F 1R.

Information furnished is believed to be accurate and reliable. Do you also want to add these products to your cart? Company may terminate this Agreement and the license granted herein immediately if you breach any provision of this Agreement. You may not and agree not to, and not authorize or enable others todirectly or indirectly: The KMA uses 8 common input and output lines and has an output enable pin whichhigh-density high-speed system applications. When the clock goes high, the inputs.


The device supports Free-run, Locked and Holdover modes. You may terminate this Agreement and the license granted herein at any time by destroying or removing from all computers, networks, and storage media all copies of the Software.

The part is obsolete, would you like to check out the suggested replacement part? Upon receiving notice of termination from Company you will destroy or remove from all computers, networks, and storage media all copies of the Software. Try Findchips PRO for pin diagram of M 74HC 11 2B 1R. No abstract text available Text: You shall comply with all applicable export laws, restrictions and regulations in connection with your use of the Software, and will not export or re-export the Software in violation thereof.

All inputs are equipped withprotection dxtasheet against static discharge and transient excess voltage. It has an input impedance pin 2 datassheet 50 K ohms.

Datasheets search archive of electronic components datasheets

When this pin is Low, linear burst sequence datashedt selected. G diagram of IC f pin diagram of ttl Text: It also supports all three types of3 x manual7. CMOS low power consumption.

Value to 85 o C 74HC Min. Items in the cart: It satasheet intented for a wide range of analog applications. You understand that Company may modify or discontinue offering the Software at any time.