CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Doukora Nimuro
Country: Malawi
Language: English (Spanish)
Genre: Software
Published (Last): 8 July 2004
Pages: 444
PDF File Size: 10.61 Mb
ePub File Size: 16.87 Mb
ISBN: 322-8-21301-842-8
Downloads: 33926
Price: Free* [*Free Regsitration Required]
Uploader: Samugul

Another way of creating VLANs is to create them in configuration mode without assigning port membership. You ccmp have to press Enter to confirm. Root guard helps prevent this by putting a port that hears these BPDUs in the root-inconsistent state.

You can configure UDLD on a per-port basis or globally for all fiber-optic gigabit interfaces.

Skills learned include the planning and execution of regular network maintenance, as well as support and troubleshooting using technology- based processes and best practices, based on systematic and industry- recognized approaches. Assign each switch a hostname according to ccnpp topology diagram. CEF implements an advanced IP lookup and forwarding algorithm to deliver maximum Layer 3 switching performance.

Use the show cdp neighbor detail command on the Gateway router to verify that ALS1 is a neighbor. This determines how far away the root bridge is.

  DIBUJO INDUSTRIAL CONJUNTOS Y DESPIECES PDF

Notice that all ports are forwarding because it is the root switch. Remember me on this computer. Notice that all the ports have identical spanning tree behavior for each VLAN.

Configure ALS1 trunking to the Gateway router. Username Password Forgot your username or password? What caused one link to be blocked over another? Configure a default gateway on the access layer switches.

ccnp-switch-instructor-lab-manual-slm

Link down Message interval: Also, the directly- connected network Configure the four switches as shown in the diagram with a hostname. Verify which switch became the root bridge. This allows the link to the router to rapidly transition to the forwarding state despite being a trunk. On 66.0 s, first set the trunk encapsulation to dot1q.

This configuration is accomplished by using the Cisco auto QoS features offered on these switches. The Cisco Networking Academy curriculum consists of three experience- oriented courses that employ industry- relevant instructional approaches to prepare students for professional- level jobs: The ports and port channel can be re-enabled after the EtherChannel is configured. Verify the EtherChannel configuration using the show etherchannel command.

CCNP SWITCH Lab Manual, 2nd Edition

The following is a sample configuration for the access manial on ALS1. B0 Motherboard revision number: How will the configuration need to be changed when a radius server is added to the network? Packet sent with a source address of Notice the use of a mamual default route. This command automatically activates access mode, PortFast, and removes all associations of the physical switch port with the port-channel interfaces if there are any.

  ESTIRANDOSE INTEGRAL PDF

Ports are identified as trusted or untrusted. DLS1 config ip dhcp excluded-address No need to be fancy, just an overview.

These are known as SVIs. If a basic unmanaged switch is connected to an access port, a broadcast storm can result, which can lead to network failure.

This is the result of the channel-group x mode being set to active. The management interface communicates with 60 management workstation in VLAN 1.

To configure a port channel as LACP, use the interface-level command channel-group number mode active. Set up the switches so that the distribution layer switches are in VTP server mode, and the access layer switches are in VTP client mode. If you instructoor the show spanning-tree mst configuration command, you can see that the current configuration reflects the changes you just committed.