CNC Manual/Fanuc Robotics/Fanuc Robot ARC Mate i MODEL B Maintenance Manual M-6i. Fanuc Robot ARC Mate i MODEL B Maintenance Manual. Refurbished Fanuc M-6i / Arcmate i with RJ2 control and pendant. Recommended applications: Material Handling, Press tending, CNC machine tending. Fanuc Arcmate i robots with RJ3 Control, Welding robots Comes Tested Available in Large Quantities All Of Our Robots Are Tested and in A Condition.

Author: Zulugami Duzshura
Country: Laos
Language: English (Spanish)
Genre: Environment
Published (Last): 26 December 2012
Pages: 148
PDF File Size: 17.24 Mb
ePub File Size: 8.39 Mb
ISBN: 842-4-39453-804-3
Downloads: 23275
Price: Free* [*Free Regsitration Required]
Uploader: Daitilar

Fanuc ARCMATE I R-J2 communication in Fanuc Robot Forum – Page 1 of 1

Thanks again for the help from forum members! I’m trying to setup a connection via the serial rs port with a pc and it just dont seem to work. Started by zaneta30 on Fanuc Robot Forum. Started by Dave on Used Robots and parts. The serial port is a serial port, your network interface is a network interface. I am using a Fanuce Arcmate i with an Rj2 controller to weld ends on to long aluminium extrusions.

Any insight on Fanuc programming is welcome. This will not work. This works well the only headache is adjustments to the program need to be done in 4 places. Perhaps someone will chime in. December 24, I move the tip to the corner of the work piece using the pendant and save that point as a second position register.

To my knowledge, the Fanuc controller does not support this, so regardless of what you do on your laptop you cannot use the program you mentioned and expect it to work. Thanks to Biozombie, The parts are longish beams, I use the rotary fixture so that I mount the part once for each end and can the weld all round in stages.


RJ controller – has RSC 25pin on front. Agcmate think I understand the problem 100u are talking about though.

Fanuc Arcmate i Rj2 Controller in Fanuc Robot Forum – Page 1 of 1

So I tried a couple pieces of software – Serial-to-Ethernet “Bridge” software. I’m rather surprised your it guy didn’t know this. It comes with Arcmare. I’m still hunting for a copy of Kfloppy so I can simplify the whole matter and get my two old RJs backed up.

Once the program starts it moves to a point on the fixture center punch mark which is in a different 10i for every orientation of the fixture, I just check that it lines up and start the next cycle. Advertisement Guest Advertisement Guest.

I have now copied and pasted the program so that it runs 4 times in one program, there is a pause programmed in for me to turn the fixture and mount the next part.

Do you have access to the Fanuc CRC? My success was as far as actually seeing packets of info get transferred when I would try to backup TP programs from the teach pendant.

I am registered with Fanuc but waiting to hear back from them. Thanks again for the input!

  ISO 10555-3 PDF

Fanuc Arcmate 100i Rj2 Controller

If you make any headway, please share the details. I was of the understanding that the STE Bridge software would create this connection, which could then aecmate picked up on the network – or better yet, on the server laptop itself. I found my old desktop with WinXP on it, and a serial port on the back.

If I used fixed stations I end up clamping and unclamping the part six or eight times depending on access. ERBU free demo version is all I need to make simple backups.

Robot used Fanuc – Fanuc Arcmate 100i Arc Welding Robot With Panastar RF350 Welding Power Source

I do NOT have K-floppy software. Here is where I am struggling, I can use the program shift utility to move the relevant sections of the program manually but I would like to do it from arcmare the program. And welcome to the forum! It cannot be reconfigured to listen to the serial port. I guess if I understand correctly, Kfloppy is 10i0 for serial protocol and will avoid the need for any other software or hardware other then the fabricated cable. I do not yet have access to the CRC.