2N6489 DATASHEET PDF

2N 2N 2N DESCRIPTION. ·With TO package. ·Excellent safe operating area. ·Complement to type 2N 2N 2N respectively. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N datasheet, 2N circuit, 2N data sheet: MOSPEC – POWER TRANSISTORS(15A,75W),alldatasheet, datasheet, Datasheet search site for.

Author: Zulkizilkree Zugul
Country: El Salvador
Language: English (Spanish)
Genre: Music
Published (Last): 19 August 2006
Pages: 462
PDF File Size: 16.4 Mb
ePub File Size: 14.85 Mb
ISBN: 396-3-90291-165-9
Downloads: 8958
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzshura

The task of regulating the output voltage is left to the control circuit which closes the loop from the output to the inverter. Foldback Current Limiting A disadvantage of the constant current limit datasheett is that in order to obtain sufficient SOA the pass element must have a much datasheef collector current capability than is actually needed. RMS and Peak repetitive rectifier current ratings can be datasheer from Figure It turns out that FET’s can be directly coupled to many IC’s with only to mA of sink and source output capability and still switch efficiently at 20 kHz.

The two transistor variation of this circuit Figure C eliminates the clamp winding and adds A. For this example, a thermalloy heatsink having a 6cs of 6. The circuit shown in Figure may be used with almost any type of regulator circuitry; however, the circuit shown in Figure should only be used in linear type supplies where the filter capacitor is isolated from the line.

Conversely, if the secondary does not take up a datasheeg layer, try bifilar winding parallel using wire half the size originally chosen; i. The out-of-phase secondary halves of Tl are cross connected through the core of T4, forming a 1-tum primary.

If the surge current cannot be reduced by adding series resistance — see Datazheet to a safe level which is consistent with the system’s requirements for speedy bus voltage re- duction, the designer must use a higher current SCR. As the load is removed or input voltage increases, a slight rise in output voltage will signal the control circuit to deliver narrower pulses to the inverter, and conversely, as the load is increased or input voltage decreases, wider pulses will be fed to the inverter.

In order to determine Vz, consider Figure l-3b. Proper attention to circuit layout is therefore necessary in order to prevent regulator instability or oscillations, or degraded performance. A clamp dayasheet is usually present to allow energy stored in the leakage reactance to return safely to the line instead of avalanching the switching transistor. The curves shown in Figures through give all the required design information for half- wave and full- wave rectifier circuits.

  JACEK KACZMARSKI SPIEWNIK PDF

In addition, the secondary windings are unregulated, so output voltages vary with line and load variations more than they do in the case of a flyback transformer.

The required 0sa for the heatsink is then determined using Equations For illustrative purposes, pass elements for only positive regulator types will be discussed. Since that time, various semiconductor companies recognized the de- signer’s needs for a dedicated control IC.

Transformer tests in the actual supply are usually done with a high voltage dc power supply on the primary and with a pulse generator or other manual control datashdet the pulse width drive such as using the control IC in an open loop configuration.

Datasheets from 07 Marth

For the output section, most designers use Schottkys for efficient rectification of the low voltage, 5. R2 is then given by: This involves checking the turns per inch of wire against the bobbin length.

Hr can be determined from Figure Pin 10 is ground for the G suffix package only. Another more subtle advantage of this circuit is that the input filter capacitors are placed in series across the rectified Vac line which allows them to be used as the voltage doubler elements on a Vac line.

Since the voltage on the capacitor is proportional to the remaining charge, the remaining time the power supply will function can be calculated by the equation: The designer may elect to use a commercially available heatsink, or if packaging or economy demands it, design his own. Motorola does not assume any liability arising out of the application or use of any product or circuit herein described.

Derating factors may be found in the transistors’ data sheets. Depending on Vin, Ta, heatsinking and package utilized, output currents in excess of mA can be obtained with this configuration.

Proportional Base Drive Figure With this configuration, the amplifier that demands minimum output on time, dominates control of the loop. Output Current Boosting Figure B shows a configuration for obtaining increased output current capability from the MCIMCI regulator by the use of an external series pass element s.

  C# VARBINARY MAX PDF

The latter figure is the same configuration as Figurewith amplifier input offset voltage and output impedance deleted for clarity and common-mode voltage effects added.

Most problems associated with mounting can be avoided if the following rules are observed: Absence of 1 mA “minimum” load see load regulation test spec on device data sheet 3. If the lead length from the input supply filter capacitor to the regulator input is more than a couple of inches, a 0. Rectification Schemes In this section, specification of the filter capacitor, dahasheet and transformer ratings will be discussed.

The value 2n648 C D can be found from Figure Ground Loops and Remote Voltage Sensing Ground Loops Regulator performance can also suffer if ground loops in the circuit wiring are not avoided.

If lower output currents are required, an MC78M05C 0. Constant Current – Zener Reference The Bandgap Reference 2n66489 very stable, the circuit of Figure 1 -4 does have a disadvantage in that it requires a supply voltage of 9 volts or more. Trial and error will indicate how low the resistor has to be to provide the correct amount of snubbing.

Zener Clamp and Snubber for Single Transistor Converters Most Switchmode transistor load lines are inductive during turn on and turn off.

2N6481 Datasheet, Equivalent, Cross Reference Search

No evidence of core saturation 2. The TL has an internal 5. Now, the output ripple can be determined. This list is only representative. Similar in many respects to the MC, the MC may also be programmed for under voltage detection 1.

Full text of “Motorola Seminarsand Application Books Rectifiers And Zener Diodes Data OCR”

Most control circuits generate a fixed frequency internally and utilize pulse width modulation techniques to implement the desired regulation. All of these devices utilize the same basic circuit configuration as shown in Figure A.

Output polarity reversal 2.